B1BB1EK1 - 307 EW10J4 ENGINE
IDENTIFICATION, DATA, TIGHTENING TORQUE(S) ENGINE
1 - IDENTIFICATION
Identification marking comprising :
2 - DATA
| engine type | EW10J4 |
|---|---|
| engine code | RFN |
| special features | without |
| unit reference | UNK. |
| number of cylinders | 4 |
| bore x stroke (mm) | 85 x 88 |
| capacity (cm3) | 1997 |
| compression ratio | 10.8 |
| maximum power : KW : EC | 100 |
| maximum power : HP DIN | 138 |
| engine speed at max. power (r.p.m.) | 6000 |
| maximum torque : da.Nm : EC | 19 |
| engine speed at max. torque (r.p.m.) | 4100 |
| turbocharger | UNK. |
| exchanger | UNK. |
| turbocharger pressure : bar(s) | UNK. |
| fuel system | multipoint |
| make | MAGNETTI MARELLI |
| type | MM 4.8 P |
| UNK. : not fitted with the function or the device in question or value does not exist N/A : value not known or not communicated |
|
3 - TIGHTENING TORQUES
3 - 1 - POWER TRAIN MOUNTINGS
| reference/description | da.Nm | da.Nm |
|---|---|---|
| special features | BE4 | AL4 |
| (1) support plate | 6 | 6 |
| (2) right engine mounting fastener | 6 | 6 |
| (3) right engine mounting fastener | 4.5 | 4.5 |
| reference/description | da.Nm | da.Nm |
|---|---|---|
| special features | BE4 | AL4 |
| (4) torque reaction rod fastener | 4 | 4 |
| (5) rod to torque reaction link flexible mounting fastener | 5.5 | 5.5 |
| (6) torque reaction link flexible mounting fastener | 4.5 | 4.5 |
| reference/description | da.Nm | da.Nm |
|---|---|---|
| special features | BE4 | AL4 |
| (7) gearbox mounting fastener | 2 | 2 |
| (8) battery tray tie-rod fastening(s) | 1 | 1 |
| (9) flexible mounting to bracket fastening | 3 | 3 |
| (10) gearbox mounting fixing to left side flexible block | 6.5 | 6.5 |
| (11) the shaft | 5 | 5 |
3 - 2 - CRANKSHAFT AND CONNECTING RODS
| (15) crankshaft bearing cap casing | ||
|---|---|---|
| reference/description | da.Nm | da.Nm |
| special features | bolt ø 11 mm | bolt ø 6 mm |
| pre-tightening | 1 | 0.5 |
| slackening | yes | no |
| tightening | 1 then 2 | 1 |
| angular tightening (°) | 70° ± 5° | without |
| (16) big end caps | |
|---|---|
| reference/description | da.Nm |
| special features | without |
| pre-tightening | 1 |
| slackening | yes |
| tightening : da.Nm | 2.5 |
| angular tightening | 46° ± 5° |
| (17) flywheel/crankshaft assembly | |
|---|---|
| reference/description | da.Nm |
| special features | without |
| pre-tightening | 2.5 |
| slackening | 180° |
| tightening | 1 |
| angular tightening | 22° ± 5° |
3 - 3 - CYLINDER HEAD EQUIPMENT
| cylinder head equipment | |
|---|---|
| reference/description | da.Nm |
| special features | without |
| (18) camshaft bearing casting ( pre-tightening ) | 0.5 |
| (18) camshaft bearing casting ( tightening ) | 1 |
| (19) cylinder head cover ( pre-tightening ) | 0.5 |
| (19) cylinder head cover ( tightening ) | 1.5 |
| (20) inlet manifold ( tightening ) | 1 |
| (21) exhaust manifold ( tightening ) | 3.5 |